0086-21-58386256
The following documents are to be used to control the quality of the entire project in the execution of the method statement for post-tensioning of concrete slab activity: Pre-pour inspection record; Stress/stressing result; Grouting; Coil log; Daily Report; Weekly report; Health and Safety Documents. Safety Manual Safety Risk Assessment
Structural Analysis Methods for the Assessment of Reinforced Concrete Slabs . JIANGPENG SHU . Department of Architecture and Civil Engineering . Division of Structural Engineering . Concrete Structures . CHALMERS UNIVERSITY OF TECHNOLOGY . Göteborg, Sweden 2017
T he scope of this method statement is to provide as guideline to ensure the fundamental checks and good working practices during Slab on Grade Concrete with respect to Project specification, Approved drawings, Material submittal, method statements This activity should be performed with strict compliance and implementation of Safety …
This method statement specifies the procedures and methods to be employed for placing, pouring, curing, and repairing concrete works and blinding concrete. Before placing any concrete or pouring any concrete, all quality checks must be accomplished, and the "approval to concrete" instruction provided by the client/consultant.
1. One-Way Slabs on Beams. Cast in situ method is used to construct one-way slabs on beams which involves fixing of forms followed with the installation of reinforcements, and finally the pouring of fresh concrete. …
Using a mobile / tower crane that suits the required load of the concrete pieces, the cut concrete pieces will be lifted/lowered to the ground by using the steel chain that will be connected to the two cores in each piece. When the concrete pieces reach the ground level, they will be carted away outside the site to the approved dumping areas. The DB …
Calculation The expression used for computing moisture vapor emission rate (MVER) is as follows: Where: MVER: moisture vapor emission rate, : change in mass (weight gain) of anhydrous CaCl2 in g A: contact area of the flanged cover on concrete in meter square deducting the area of the CaCl2 dish T: exposure time in hours. 3. Other Methods The …
Sawcutting an Existing Structural Slab. We have to cut a 2x2-foot opening in an existing elevated reinforced-concrete slab. An engineer has approved the location of the opening, but we're trying to decide the best way to cut it. ... We'd opt for the cutting method that's most economical. About the Author Concrete Construction Staff ...
2. Scope. The Scope of this method statement covers the various requirements to be provided for preparation like chipping and expose the existing rebar, marking to position the new starter bar …
This document provides a method statement for slab and beam concreting for the construction of 500 housing units. It outlines the materials, equipment, manpower, and …
Therefore, the two major forms of construction of ribbed slabs are; (1) Ribbed slab without permanent blocks (2) Ribbed slab with permanent blocks. The major advantage of a ribbed slab with …
This method statement covers the detailed procedure to be followed for screeds/topping operation above water proofing in toilet, roof slab and raft slab. Method statement also covers the screeding operation below tiling works in concrete slabs wherever necessary. This floor screeding procedure shall be read in conjunction with contract civil …
1. The document provides guidelines for cutting existing concrete slabs, including using saw blades and temporary shading to protect against deterioration. 2. It describes …
Below is a precise civil work method of statement that covers the detailed procedure for the scaffolding / formwork, rebar installation and concreting operation applicable for footing, …
Another class of applications includes the strengthening of existing concrete structures, often to improve performance e.g. due to refurbishment (Figure 5). Image bank COS_0241.jpg Figure 4a Column extension.jpg Figure 4b Slab-to-slab connection.jpg Figure 4c Slab-to-wall connection.jpg Image bank L008728.jpg
A construction joint is one of the types of joints in site construction that can be located on walls and slabs. The most popular usage of construction joints is on suspended slabs. Literally, it is defined as a longitudinal cut in the slab during the concrete pouring process. It is termination on the slab during the concreting works.
References. Project Specifications Formwork System Approved Shop Drawings Material Approval Lifting Plan & Procedure HSE Plan-Health, Safety & Environment Plan Project Quality Plan BS 8666: 2020. Tools. Total station Level machine Plywood base plates Water level Nylon chord Masking tape Spanners. Equipment. Mobile Crane/Tower Crane
At slab edges, curve the mesh down into the perimeter footings (Figure: Forming a Structural Slab in Site Layout for Structural Slabs). Do not lap wire sections at joints. Instead, stop the mesh several inches back from the joint location. If control joints are spaced close together, and a low-slump mix is used, wire mesh is probably not necessary.
Shotcreting method is useful for: concrete repair of large areas of concrete deteriorated due to reinforcement corrosion or other reasons, strengthening of existing concrete columns, beams and slabs by increasing the concrete sectional area by the application of shotcreting and by increasing the steel and construction of structures with complex ...
Communicate method statement: Communicate to all relevant parties (via a toolbox talk) and ensure it is signed by all personnel. This method statement was prepared by: R. Leveller. Date: 01/03/11. (Note - this method statement has been developed using the site specific risk assessment, the
repair by epoxy injection can restore structural integrity and reduce moisture penetration through concrete cracks 0.002 in. (0.05 mm) in width and greater. However, before any concrete repair is carried out, the cause of the damage must be assessed and corrected and the objective of the repair understood. If the crack is subject to subsequent ...
Method Statement Sika® Crack Injection, structural 30.04.2021, Version 5 2/12 TABLE OF CONTENTS 1 Scope 3 2 Description 3 2.1 Limitations 3 3 References 3 4 Products 3 4.1 Material Storage 3 5 Equipment 4 5.1 Injection equipment 4 6 Health and safety 6 6.1 Personal protection 6 6.2 First aid 6 7 Environment 7
Approval must be obtained from the Engineer for waterproofing and backfilling works prior to start slab on grade casting. Here is the method statement for pouring concrete on Slab on Grade preparation and concrete pouring. 1. Title. Method Statement for Casting or pouring concrete on Slab on Grade. 2. Purpose and scope
In this Article: Method Statement for Concrete Repair Works, Structural Works, Repair of Concrete Cracks, Structural Concrete Repair, Steps for Concrete Damage Repair
Guide for Concrete Floor and Slab Construction, ACI 302.1R, American Concrete Institute, Farmington Hills, MI. 3. Slabs on Grade, ACI Concrete Craftsman Series CCS-1, American Concrete Institute, Farmington Hills, Ml. 4. Joint Planning Primer, Concrete Construction, August 1997. 5. Bruce A. Suprenant, Sawcutting Joints in Concrete, Con-
This method statement for demolition works of building such as soft stripping, scaffold erection, demolition, foundation/hard standing removal, and crushing to a certified 6F2 aggregate is detailed for the agreed-upon works at the site. ... Method Statement for In-situ Concrete & General Concrete Work; ... Removal of the slab, footings, and ...
