0086-21-58386256
Tons vs. Cubic Yards. One ton of crushed stone weighs between 2,000 and 2,800 pounds. This depends on the stone type and its density. A cubic yard of crushed stone weighs from 1.4 to 1.9 tons, also based on the material's density. The weight per cubic yard can change a lot, so it's good to know the stone's specifics.
1 Cubic Yard Crushed Stone (0-19 mm / 0 ... About a 1/3 of it was filled with what looked like limestone screening and another 1/3 with rocks much bigger than 3/4". ... was also vary happy with the size and quality of the crush rock dropped off. Will order again for my next project. Date published: . 1 Cubic Yard Crushed Stone (0-19 ...
The calculator determines the volume of crushed limestone you need in cubic yards. It follows these steps: Converts the depth from inches to feet. Multiplies the length, width, …
A final calculation is if you need to figure out the weight in tons of your crushed stone. You might not need to figure this out, but it's handy to know. Most gravel weighs about 1.5 tons per cubic yard. So, for the examples above, 2.45 cubic yards of gravel weighs 3.68 tons or 7,350 pounds.
Limestone Gravel: Mulch: Mulch, Bark & Bedding: Pool Sand & Beach Sand: Premium Pebbles Bulk Bag: Recycled Materials: Rip Rap / Boulders: River Gravel / Pea Gravel: Road Grit / Salt : Rubber Mulches: RV Pads & Sheds: Sand / Screenings: Sand for Pavers: Sand for Underneath (Laying) Pavers: Search by Application : Soil & Dirt: Soil & Dirt: Stone ...
We deliver from gravel pits, quarries and stock yards in Alabama, Arizona, Arkansas, California, Florida, Georgia, Indiana, Illinois, Kentucky, Louisiana, Michigan ...
If your number comes out as a fraction, round up. In the example above, you would round the 3.7 cubic yards of crushed stone to 4 cubic yards of crushed stone. It is better to have a little extra than to run short.
How to Find Cubic Yards of Base Material. To estimate the cubic yards of gravel needed for a paver base, follow these steps: Step One: Measure the length and width of the patio in inches Step Two: Multiply the length and width to find the area in square inches Step Three: Multiply the area by the gravel depth in inches to find the volume in cubic inches – …
3/4 Crusher Run. $45.00 / Cubic Yard; 3/4 Crusher Run available for pick up and delivery. Add To Cart More Info. Limestone Screenings. $40.00 / Cubic Yard; Limestone Screenings available for pick up and delivery. Order Online! Add To Cart More Info. HPB (High Performance Bedding) $45.00 / Cubic Yard;
Minus crushed rock costs $12-$35 per cubic yard while clean crushed rock costs $30-$50 per cubic yard. Delivery and spreading can double those prices. However, the more material you order, the less the total cost. Delivery is usually free of charge up to 10 miles. Below are some crushed stone/gravel delivery prices by locations:
Is crusher run cheaper than gravel? At $0.40 per square foot, crusher run is significantly cheaper than regular gravel, which sells at about $0.70 per square foot. A ton of plain gravel sells at an average price of $50, which is about $20 dollars more than the price of a similar amount of crusher run. Does crusher run drain well?
The basic cost to Install Crushed Stone is $0.94 - $1.82 per square foot in April 2024, but can vary significantly with site conditions and options. Use our free HOMEWYSE CALCULATOR to estimate fair costs for your SPECIFIC project. See typical tasks and time to install crushed stone, along with per unit costs and material requirements. See …
Calculate Crusher Run. Type in inches and feet of your project and calculate the estimated amount of Base Material in cubic yards, cubic feet and Tons, that your need for your project. The Density of Crusher Run : 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t. Type in …
The average price of crusher run, also know as 'Crush and Run' is $25 to $35 a ton. Sometimes people buy it at $1 to $5 per sq.ft. or $30 to $40 per cubic yard instead. This material is a fine mixture of crushed stone and stone dust.
We sell compact crusher run and 57 limestone for driveway in cubic yards or square feet. Need professional guidance on muddy and erosive areas or unsure whether to install …
Type in inches and feet of your project and calculate the estimated amount of Base Material in cubic yards, cubic feet and Tons, that your need for your project. The Density of Crusher Run : 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t
The calculator determines the volume of crushed limestone you need in cubic yards. It follows these steps: Converts the depth from inches to feet. Multiplies the length, width, and converted depth to get the volume in cubic feet. Converts the volume from cubic feet to cubic yards (since there are 27 cubic feet in a cubic yard). Limitations
Your calculation of the area for a 20' x 20' wide with a depth of 6" would give you a volume needed of 20 * 20 * .5 = 200 cubic feet. From the first example, the compaction factor = 1.237 based on 15% swell and -7% shrink for this material. Convert 200 cubic feet to cubic yards = 200/27 = 7.4 cubic yards 7.4 cubic yards * 1.237 = 9.15 cubic yards.
Crushed Stone Gravel – $38.50 Per Ton. This is made from larger stones crushed into smaller pieces. It's often used for driveways and as a base material for …
Find out how much does a ton of #57 stone cost. Read on! Dirt Connections ... Limestone is the most common type of rock used for #57 stone in the United States, although many other types are also readily available. This type of stone is prized for its versatility. ... One truckload of this rock is roughly equal to 10 to 12 cubic …
A cubic yard block of limestone weighs approximately 2.0 US tons or roughly around 4,000 pounds. On the other hand, a cubic yard box filled with crushed …
How Much Does 1 Meter Of 3/4 Crusher Run Weigh In Gujarat … how much does 1 cubic meter of rock weigh « BINQ Mining. Apr 24, 2013 · What is the weight of 1 yard of crush and run …
Type in inches and feet of your project and calculate the estimated amount of Gravel Stone in cubic yards, cubic feet and Tons, that your need for your project. The Density of 6A Limestone: 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t ... Crusher Run Near Me - Prices and Delivery; Bulk Mason Sand Near Me - Prices and Delivery;
Installing a gravel driveway costs between $300 to $4,500, or an average of $1,500, including labor and materials.Your bottom line can run much higher for extra related services like land clearing ...
It may often look like sand, though it is actually part of the process of crushing limestone, granite or whatever is local to your market for coarse aggregates. Crusher run weighs …
Crush and run driveway costs are $1 to $2 per cubic foot, $51 to $54 per cubic yard, or $24 per ton or more. Top-layer crusher run stone is 0.75" rock with particles, like quarry process or #411 gravel. …
Type in inches and feet of your project and calculate the estimated amount of Base Material in cubic yards, cubic feet and Tons, that your need for your project. The Density of Crusher Run 3/8" minus: 2,480 lb/yd³ or 1.24 t/yd³ or 0.8 yd³/t
Click the Calculate button to get the amount of crushed stone needed in cubic yards. How it Calculates the Results. This calculator uses the following steps to calculate the amount of crushed stone needed: Converts the depth from inches to feet by dividing by 12. Multiplies the length, width, and depth in feet to get the volume in cubic feet.
Type in inches and feet of your project and calculate the estimated amount of Recycled Materials in cubic yards, cubic feet and Tons, that your need for your project. The Density of Crushed Concrete Paver Base: 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t
Type in inches and feet of your project and calculate the estimated amount of Gravel Stone in cubic yards, cubic feet and Tons, that your need for your project. The Density of #357 Limestone Gravel: 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t
Contribute to dinglei2022/en development by creating an account on GitHub.
@Mazura -- Seattle's major rock and topsoil vendor sells crushed rock in increments from 5 gallons to the truckload. The bulk price (for picking up material at the vendor's yard) is available in quarter of a cubic yard increments. A quarter of a cubic yard is enough to fill 10 5-gallon buckets. –
About 2.47 cubic yards without considering the waste factor, and 2.72 cubic yards with a waste factor of 10%. That's 3.7 and 4.1 US tons, respectively. To calculate …
A typical load of gravel is usually around 8 to 20 cubic yards, weighs 10 to 20 tons, and can cost anywhere from $500 to $1,200, depending on the multiple factors. ... terms of size and composition. #610 gravel tends to be larger in particle size due to being composed mainly of crushed limestone while crusher run gravel contains fines from both ...
About #57 Limestone Gravel #57 Stone is a crushed angular Limestone aggregate. Sizes of #57 Stone range from 1/2" to 1". #57 is one of the most popular and common gravels as it has a wide range of applications. …
In the Udden-Wentworth scale, gravel is categorized as granular gravel if it is 2-44 mm (0.079-0.157 in) in diameter or pebble gravel if it is 4-66 mm (0.2-2.5 in) in diameter. On the other hand, ISO 14688-1:2002 classifies gravel as fine (2.0-6.3 mm), medium (6.3-20 mm), or coarse gravel (20-63 mm). How much gravel do I need?